Processing Aids & Plasticizers

Norac® EL-15 is an ester used as a highly compatible internal lubricant with good release and flow properties for rigid and semi-rigid PVC transparent applications. It works well in PVC water bottles where low blush is desired.

RPVC profiles, fittings, sheets, foam, Allows for a wider process window, and Polycarbonate processing.

RPVC bottles, extruded and foamed profile, clear film and sheet, injection molded parts, Highly efficient external lubricant with superior release properties, Compatible with PVC as to not affect printability, and CFR 21.

PVC Rigid Profile & Sheet Extrusion, PVC Flexible Film & Sheet, PVC Wire & Cable, PVC Roofing Membrane, PVC Flooring & Cove Base

Norac® XL-53 is a mixed internal/external lubricant with co-stabilizing properties for extruded foamed rigid PVC profiles.

Norac® XL-63 is a mixed internal/external lubricant with co-stabilizing properties for rigid PVC foamed profile and sheet.

Norac® XL-65A is a specially formulated lubricant designed for use in PVC pipe, siding and fence.

Norac® XL-77 is a paraffin-free ester-based blend designed for rigid PVC foam and profile extrusion.

Coad® 23 Zinc Stearate Vegetable Grade reduces caking and improves flow properties. Due to its greater density, higher loadings can be obtained in certain equipment.

Coad® 25 Zinc Stearate is an excellent flatting agent and sanding aid for lacquers and lacquer sanding sealers and easily dispersed by stirring. When used as a flatting agent in paint, it also aids in pigment dispersions. Coad® 25 Zinc Stearate is an excellent mold release agent for phenolic, melamine, urea-formaldehyde, and other thermoset molding compounds. Coad® 25 Zinc Stearate is used in cream and paste formulations to stabilize water-in-oil emulsions. Coad® 25 Zinc Stearate, with its high spreading power, is used as a dusting powder for uncured rubber stocks where even, light coatings are desired. It is an excellent mold release agent and is useful as an anticoagulant in latexes.

Coad® 26 Zinc Stearate is used as a lubricant and is an excellent mold release for polymers used in indirect contact applications in compliance with FDA Title 21 CFR.

Coad® 27D Zinc Stearate at 12 microns yields lower mix viscosities while keeping the top size small enough to completely avoid surface blemishes.

Coad® 27F Zinc Stearate at 25 microns provides the lowest viscosity build by virtue of its relatively large particle size. Careful control of the top size ensures high quality surfaces with most compounds.

Coad® 30 Zinc Stearate Prill reduces caking and improves flow properties while reducing dust. Due to its greater density, higher loadings can be obtained in certain equipment.

Coad® 31 Zinc Stearate Prill is used as a lubricant and mold release agent in unpigmented crystalline and impact polystyrene
compounds. COAD® 31 Zinc Stearate Prill is an excellent mold release agent for pheolic, melamine, urea-formaldehyde, and other thermoset molding compounds where a heat stable material is required.

Coad® 33 Zinc Stearate Prill Vegetable Grade reduces caking and improves flow properties while reducing dust. Due to its greater density, higher loadings can be obtained in certain equipment.

Coad® 40 Magnesium Stearate is recommended as a flatting agent for paints, varnishes, and lacquers. It is particularly suitable for products subject to high temperature since it is comparatively insoluble in most paint vehicles even at high temperatures. It is an excellent dusting agent to prevent surface adhesion in ABS plastics and other thermoplastics with minimal discoloration.

Coad® 41 Magnesium Stearate is recommended as a flatting agent for paints, varnishes, and lacquers. It is particularly suitable for products subject to high temperature since it is comparatively insoluble in most paint vehicles even at high temperatures. It is an excellent dusting agent to prevent surface adhesion in ABS plastics and other thermoplastics with minimal discoloration.

Coad® Zinc Stearate Disperso II is used on uncured rubber stocks to prevent adhesion. Uniform coatings are deposited on slabs or extruded forms from aqueous dispersions in dip tanks or baths.

Coad® Zinc Stearate HA is an excellent flatting agent and sanding aid for lacquers and lacquer sending sealers, easily dispersed by stirring. When used as a flatting agent in paint, it also aids in pigment dispersions. COAD® Zinc Stearate HA offers a high ash content to resist blooming in reactions with acidic catalysts or substrates.

Norac® 95-V is a plant-sourced stearic acid containing 95% C18 acid.

Norac® EL-10 is an ester used as a highly compatible and efficient allpurpose internal lubricant for rigid PVC products.

Norac® EL-11 is an ester used as an intermediate lubricant for rigid and semi-rigid PVC products.

Mono-Coat® E255 is a water-thin liquid that is readyto-use as shipped. The release system becomes functional after cure. The release film is micro-thin and stable. Mono-Coat® E255 adheres to the mold surface and provides multiple releases with virtually no transfer to molded parts. This product minimizes buildup on the molds when applied according to instructions.

Compression, injection and transfer molding of all rubbers and EVA. Provides excellent release where high durability is required. (Not recommended for silicone rubber.)

Rotational Molding: Designed for superior release Rotational Molding of cross-linked polyethylenes.
Rubber Molding: Ideal for low durometer/high flow Rubber Molding rubber
stocks other than silicone rubber.

Coad® 10 Calcium Stearate acts as a dispersing aid during the blending cycle, as a lubricant and processing aid during extrusion, and as a mold release agent for injection molding. Coad® 10 Calcium Stearate is an excellent mold release agent for matched metal die molding under certain conditions. Coad® 10 Calcium Stearate acts as an anti-sticking agent for rubber slab where a dry powder is preferred. It is useful for applications with zinc discharge limitations. Coad® 10 Calcium Stearate may be employed in concrete and mortar admixtures to impart water repellency and to improve flow and release properties of the dry mix.

Coad® 10LD Calcium Stearate acts as a dispersing aid during the blending cycle, as a lubricant and processing aid during extrusion, and as a mold release agent for injection molding. It also improves stability by neutralizing acidic decomposition products in the polymerization of certain polyolefins. Coad® 10LD Calcium Stearate is an excellent mold release agent for matched metal die molding under certain conditions.

Coad® 10 B Calcium Stearate acts as a dispersing aid during the blending cycle, as a lubricant and processing aid during extrusion, and as a mold release agent for injection molding. It also improves stability by neutralizing acidic decomposition products in the polymerization of certain polyolefins. Coad® 10 B Calcium Stearate is an excellent mold release agent for matched metal die molding under certain conditions.

Coad® 13D Calcium Stearate acts as a catalyst neutralizer in polypropylene, as a dispersing aid during the blending cycle, as a lubricant and processing aid during extrusion, and as a mold release agent for molding. Specifically designed for polymers where filterability through screenpacks is critical.

Coad® 20 Zinc Stearate improves pigment dispersion and reduces blending time needed to produce uniform mixtures. It also acts as a lubricant to improve melt flow and prevents sticking to extruder surfaces. Coad® 20 Zinc Stearate shortens blending cycles, gives higher apparent densities and better flow properties in the metal powder-lubricant blends, reduces injection pressure, and improves die life. Coad® 20 Zinc Stearate is used where thick, uniform coatings are desired on uncured slabs or especially tacky formulations. Coad® 20 Zinc Stearate may be employed in concrete and mortar admixtures to impart water repellency and to improve flow and release properties of the dry mix.

Coad® 21 Zinc Stearate is used as a lubricant and mold release agent in unpigmented crystalline and impact polystyrene compounds. Coad® 21 Zinc Stearate is an excellent mold release agent for phenolic, melamine, urea-formaldehyde, and other thermoset molding compounds where a heat stable material is required.

Coad® 23 Zinc Stearate reduces caking and improves flow properties. Due to its greater density, higher loadings can be obtained in certain equipment.

Compression, injection, and transfer molding of all rubbers. Provides excellent release where high durability is required. (Not recommended for silicone rubber.)

It is specially formulated to provide excellent release from stainless steel, steel and aluminum tooling. It is particularly effective on
stainless steel substrates. Mono-Coat® 1903WRB provides high-temperature stability, excellent durability and multiple releases with virtually no transfer to the molded part.

Compression, injection and transfer molding of all rubbers. Provides excellent release where high durability is required. (Not recommended for silicone rubber.)

Compression, injection and transfer molding of all rubbers. Provides excellent release where high durability is required. (Not recommended for silicone rubber.)

Compression, injection and transfer molding of all rubbers. Provides excellent release where high durability is required. (Not recommended for silicone rubber.)

Compression, injection, and transfer molding of all rubbers. Provides excellent release where high durability is required. (Not recommended for silicone rubber.)

Compression, injection and transfer molding of all rubbers. Provides excellent release where high durability is required. (Not recommended for silicone
rubber.)

Mono-Coat® 1916WD is effective for molding operations that require low transfer of release agent, high-temperature stability and multiple releases. Mono-Coat® 1916WD is ready-to-use as shipped.

Mono-Coat® 1917WD is particularly effective with molding operations that require low transfer of release agent, high-temperature stability and multiple releases. Mono-Coat® 1917WD is ready-to-use as shipped.

Mono-Coat® 1918WD is effective for molding operations that require low transfer of release agent, high-temperature stability and multiple releases. Mono-Coat® 1918WD is ready- to-use as shipped.

Rubber Molding: Compression, transfer, and injection of typically difficult-to-mold compounds

Mono-Coat® 1924D is a water-thin liquid that is readyto-use as shipped. The release system becomes functional after cure. The release film is micro-thin and stable. This product minimizes buildup on the molds when applied according to instructions.

Compression, injection, and transfer molding of most rubber compounds as well as thermoplastics such as TPU or TPO compounds. Provides excellent release where high durability is required. (Not recommended for silicone rubber.)

Compression, injection and transfer molding of all rubbers. Provides excellent release where high durability is required. (Not recommended for silicone rubber.)

Compression injection and transfer molding of all rubbers. Provides excellent release where high durability is required. (Not recommended for silicone rubber.)

Mono-Coat® 2048W is effective for a variety of rubber compounds and molding operations that require low transfer of release agent, high-temperature stability and multiple releases. Mono-Coat® 2048W is ready to use as shipped.

Mono-Coat® A1555W is effective for molding operations that require low transfer of release agent, high-temperature stability and multiple releases. Mono-Coat® A1555W is ready to use as shipped, or can be diluted with good quality water, according to the release needs of the molded article.

Rotational molding – All types, i.e. XLPE, HDPE, MDPE, LDPE, LLDPE and Rubber molding – Natural, SBR, nitrile,and other polymers except silicone (injection, compression, transfer)

Mono-Coat® E76 NODS contains no Ozone Depleting Substances (ODS). Mono-Coat® E76 N-ODS adheres to mold surfaces and produces multiple releases with virtually no transfer to molded parts. This product leaves virtually no buildup on the mold when applied according to instructions.

Rubber molding: All types including EVA (not recommended for silicone rubbers.)

Mono-Coat® 370W is effective for molding operations requiring low transfer of the release agent, hightemperature stability, and multiple releases. It keeps tooling cleaner longer, reducing downtime. MonoCoat® 370W is ready-to-use as shipped.

Mono-Coat® 438W is effective for molding operations that require minimal transfer of the release agent, high-temperature stability, multiple releases and a high degree of slip. Mono-Coat® 438W is ready-to-use as shipped.

Mono-Coat® 1175W is designed for application on the hot mold. If applied to a cold mold, corrosion may result. We recommend a
thorough cleaning of the mold followed by a solvent wipe to remove any residue before preheating the mold.

Compression injection and transfer molding of all rubbers. Provides excellent release where high durability is required.

Mono-Coat® 1582W provides nontransfer of release agent, high-temperature stability and excellent abrasion resistance.
Mono-Coat® 1582W cures rapidly, is ready-touse as shipped and is suitable for compression injection and transfer molding of all rubber
compounds, including silicone rubber.

Mono-Coat® 1586 adheres to mold surfaces and provides multiple releases with virtually no transfer to molded parts. This product leaves virtually no buildup on the molds when applied according to instructions.

Mono-Coat® 1625W is effective for molding operations that require low transfer of release agent, high-temperature stability and
multiple releases. Mono-Coat® 1625W is ready to use as shipped.